FreeAvailable now — free

Basic Flow Calculator

Preliminary flow calculations for fire fighting systems.

Project & Input Data

Your project criterion: enter the value from your governing code, specification or approved supplier data. No standard value is assumed.

Your project criterion: enter the value from your governing code, specification or approved supplier data. No standard value is assumed.

Your project criterion: enter the value from your governing code, specification or approved supplier data. No standard value is assumed.

Embedded standards & references

  • Declared density-area identity; project fire criteria

Results are engineering aids and require verification by a qualified professional before use on a real project.

Engineering Assumptions

Direct calculation — Bounded water path or density-area demand

  • Three-phase voltage is line-to-line with balanced sinusoidal load and lagging displacement factor. Power input is electrical, not mechanical output. No imbalance, harmonics or motor-efficiency model. Independent S is not merged with P/PF.
  • Voltage drop is approximate using operating-temperature resistance and path reactance from product data, with one-way length. No assumed temperature correction, ampacity or protection. Capacitors are Q arithmetic only, no stage/resonance selection; a target below existing PF gives zero correction, not reduced PF.
  • Water pressure is one path at actual internal diameter, water1000kg/m³ and g=9.80665. Hazen-Williams is empirical for water, not all fluids. Elevation is signed. Equivalent lengths and devices must not be duplicated. Compare at the same flow/pressure; no pump or fire-network approval.
  • Density×area demand does not simulate actual sprinkler overdischarge or balancing. Density/area/hose values require project evidence; defaults are examples, not rules. Comparison success is not conformity certification.
  • https://www.electrical-installation.org/enwiki/Calculation_of_voltage_drop_in_steady_load_conditions
  • https://www.electrical-installation.org/enwiki/How_to_calculate_the_level_of_reactive_energy_compensation
  • https://www.epa.gov/water-research/epanet

Formula Summary

  • Demand=density×area+hose allowance; L/s=L/min÷60; shortfall=max(0,demand−supply)

Built-in definitions, not code limits

DefinitionValue
g9.80665m/s²
Assumed waterρ1000kg/m³
Hazen-Williams SI10.67;1.852;4.871

SI constants and declared engineering relations

Results

Enter your data and press Calculate to see the results.

Engineering Insight

Keep measurements and independent inputs separate from the calculated identity; results neither design equipment nor certify conformity.

Recommended Action

Document P/S, R/X or C and pipe diameter sources; check the same operating conditions before engineering review.

Sprinkler demand is the starting point for pump and storage discussions. Enter the design density and design area taken from the standard governing your project, add the hose-stream allowance, and the calculator returns the sprinkler flow and the total demand in litres per minute.

Method and assumptions

Bounded water path or density-area demand

  • Demand=density×area+hose allowance; L/s=L/min÷60; shortfall=max(0,demand−supply)
  • Three-phase voltage is line-to-line with balanced sinusoidal load and lagging displacement factor. Power input is electrical, not mechanical output. No imbalance, harmonics or motor-efficiency model. Independent S is not merged with P/PF.
  • Voltage drop is approximate using operating-temperature resistance and path reactance from product data, with one-way length. No assumed temperature correction, ampacity or protection. Capacitors are Q arithmetic only, no stage/resonance selection; a target below existing PF gives zero correction, not reduced PF.
  • Water pressure is one path at actual internal diameter, water1000kg/m³ and g=9.80665. Hazen-Williams is empirical for water, not all fluids. Elevation is signed. Equivalent lengths and devices must not be duplicated. Compare at the same flow/pressure; no pump or fire-network approval.
  • Density×area demand does not simulate actual sprinkler overdischarge or balancing. Density/area/hose values require project evidence; defaults are examples, not rules. Comparison success is not conformity certification.
  • https://www.electrical-installation.org/enwiki/Calculation_of_voltage_drop_in_steady_load_conditions
  • https://www.electrical-installation.org/enwiki/How_to_calculate_the_level_of_reactive_energy_compensation
  • https://www.epa.gov/water-research/epanet

Worked example

A design density of 6 L/min·m² over a 140 m² design area, with a 500 L/min hose-stream allowance — all three values taken by the user from the project's governing standard.

Worked example results
ResultValue
Declared density-area product840 L/min
Independent hose allowance added once500 L/min
Theoretical total demand, not network1,340 L/min
Flow in L/s22.33 L/s
Supply shortfall at same duty pressure1,340 L/min

These figures are produced by the same calculator engine used on this page.

Frequently asked questions

Does the tool know my hazard classification?
No. Density, area and hose allowance are all user-entered. The engine contains no density/area table and infers nothing about occupancy or hazard.
Is this a hydraulic calculation?
No. It is the demand flow only. Pipe network hydraulics, pressure balancing and node-by-node analysis are separate work and are not performed here.
What can I do with the result?
Use it as the input flow for storage and pump sizing discussions — the Fire Water Tank and Fire Pump estimate tools take a duty flow of this kind.
Can it replace an approved fire design?
Never. Fire protection design must be produced and approved by a competent licensed fire engineer and accepted by the authority having jurisdiction.

Next step and related links

Free calculators are open to everyone, and CSV export is free for everyone too. Project saving and PDF/Excel reports come with Professional, and integrated workflows with Premium.