FreeAvailable now — free

Pressure Calculator

Preliminary pressure calculations.

Project & Input Data

Your project criterion: enter the value from your governing code, specification or approved supplier data. No standard value is assumed.

Your project criterion: enter the value from your governing code, specification or approved supplier data. No standard value is assumed.

Your project criterion: enter the value from your governing code, specification or approved supplier data. No standard value is assumed.

Embedded standards & references

  • EPA EPANET2.2(2020) SI Hazen-Williams relation; not complete NFPA

Results are engineering aids and require verification by a qualified professional before use on a real project.

Engineering Assumptions

Direct calculation — Bounded water path or density-area demand

  • Three-phase voltage is line-to-line with balanced sinusoidal load and lagging displacement factor. Power input is electrical, not mechanical output. No imbalance, harmonics or motor-efficiency model. Independent S is not merged with P/PF.
  • Voltage drop is approximate using operating-temperature resistance and path reactance from product data, with one-way length. No assumed temperature correction, ampacity or protection. Capacitors are Q arithmetic only, no stage/resonance selection; a target below existing PF gives zero correction, not reduced PF.
  • Water pressure is one path at actual internal diameter, water1000kg/m³ and g=9.80665. Hazen-Williams is empirical for water, not all fluids. Elevation is signed. Equivalent lengths and devices must not be duplicated. Compare at the same flow/pressure; no pump or fire-network approval.
  • Density×area demand does not simulate actual sprinkler overdischarge or balancing. Density/area/hose values require project evidence; defaults are examples, not rules. Comparison success is not conformity certification.
  • https://www.electrical-installation.org/enwiki/Calculation_of_voltage_drop_in_steady_load_conditions
  • https://www.electrical-installation.org/enwiki/How_to_calculate_the_level_of_reactive_energy_compensation
  • https://www.epa.gov/water-research/epanet

Formula Summary

  • hf=10.67×(L+Leq)×Q^1.852/(C^1.852×D^4.871), SI Q=m³/s,D=m
  • Signed inlet=remote+ρgz/100000+friction+separate device loss; required=max(0,signed)

Built-in definitions, not code limits

DefinitionValue
g9.80665m/s²
Assumed waterρ1000kg/m³
Hazen-Williams SI10.67;1.852;4.871

SI constants and declared engineering relations

Results

Enter your data and press Calculate to see the results.

Engineering Insight

Keep measurements and independent inputs separate from the calculated identity; results neither design equipment nor certify conformity.

Recommended Action

Document P/S, R/X or C and pipe diameter sources; check the same operating conditions before engineering review.

Estimate fire-system pressure for preliminary review. Enter remote pressure, elevation, flow, pipe diameter and length, fittings length and Hazen-Williams C. Free to use without signing in.

Method and assumptions

Bounded water path or density-area demand

  • hf=10.67×(L+Leq)×Q^1.852/(C^1.852×D^4.871), SI Q=m³/s,D=m
  • Signed inlet=remote+ρgz/100000+friction+separate device loss; required=max(0,signed)
  • Three-phase voltage is line-to-line with balanced sinusoidal load and lagging displacement factor. Power input is electrical, not mechanical output. No imbalance, harmonics or motor-efficiency model. Independent S is not merged with P/PF.
  • Voltage drop is approximate using operating-temperature resistance and path reactance from product data, with one-way length. No assumed temperature correction, ampacity or protection. Capacitors are Q arithmetic only, no stage/resonance selection; a target below existing PF gives zero correction, not reduced PF.
  • Water pressure is one path at actual internal diameter, water1000kg/m³ and g=9.80665. Hazen-Williams is empirical for water, not all fluids. Elevation is signed. Equivalent lengths and devices must not be duplicated. Compare at the same flow/pressure; no pump or fire-network approval.
  • Density×area demand does not simulate actual sprinkler overdischarge or balancing. Density/area/hose values require project evidence; defaults are examples, not rules. Comparison success is not conformity certification.
  • https://www.electrical-installation.org/enwiki/Calculation_of_voltage_drop_in_steady_load_conditions
  • https://www.electrical-installation.org/enwiki/How_to_calculate_the_level_of_reactive_energy_compensation
  • https://www.epa.gov/water-research/epanet

Next step and related links

Free calculators are open to everyone, and CSV export is free for everyone too. Project saving and PDF/Excel reports come with Professional, and integrated workflows with Premium.