FreeAvailable now — free

Blockwork Calculator

Estimate block counts from wall area (mortar quantities not included).

Project & Input Data

%

An editable user-defined allowance — not a universal engineering requirement.

Embedded standards & references

  • Declared area/volume and product dimensions; not structural conformity

Results are engineering aids and require verification by a qualified professional before use on a real project.

Engineering Assumptions

Direct calculation — Bounded geometric measurement and separate supply balance

  • Regular rectangular measurement only; openings cover all surfaces and cannot exceed gross area. Intermediate quantities are not rounded. RICS NRM2(2021) informs measurement boundaries, not a claim to implement every deduction rule.
  • https://www.rics.org/content/dam/ricsglobal/documents/standards/october_2021_nrm_2.pdf
  • Masonry/tiles: repeating module with joint, not a cutting layout; boundaries, bond and patterns need project take-off. No mortar, grout or strength calculation.
  • Paint uses practical product-datasheet coverage per whole coat. Plaster is wet volume only, not mix constituents. Stock matches product/unit and is allocated to this work.
  • Excavation is a vertical box only, without shoring/slope design. Swell and backfill ratio are project soil data, not code values. Backfill factor=loose/compacted volume; not an additional percentage counted twice.
  • Supply is separate from consumption; packs are whole. Excavation trips use loose volume and declared capacity; weight/road limits may increase trips. Results do not authorize construction.

Formula Summary

  • Net area = length × height × count − total openings
  • Repeating module = (unit length + joint) × (unit height + joint)
  • Paint = net area × whole coats / product coverage; plaster = net area × wet thickness
  • Earth: loose = in-situ × (1+swell); backfill loose = compacted × project ratio
  • Purchase packs = ceil(max(0, requirement − compatible stock) / pack size)

Built-in measurement definitions

QuantityIdentity
AreaL×H×N−openings
Box volumeL×W×D×N
Surplusmax(0,stock−required)+purchase−max(0,required−stock)

Declared geometric identities; no normative waste or soil factor

Results

Enter your data and press Calculate to see the results.

Engineering Insight

Ignoring mortar joints yields a slightly conservative (higher) block count, which suits initial ordering. Supplier-to-supplier block size differences change the count materially.

Recommended Action

Verify the supplier's actual block dimensions and check opening deductions against the architectural drawings before confirming the order.

Use this page when you need a block count for procurement or a bill of quantities line. It works from the net wall area and the block face size you actually specify, applies your waste percentage, and rounds up because blocks are bought whole.

Method and assumptions

Bounded geometric measurement and separate supply balance

  • Net area = length × height × count − total openings
  • Repeating module = (unit length + joint) × (unit height + joint)
  • Paint = net area × whole coats / product coverage; plaster = net area × wet thickness
  • Earth: loose = in-situ × (1+swell); backfill loose = compacted × project ratio
  • Purchase packs = ceil(max(0, requirement − compatible stock) / pack size)
  • Regular rectangular measurement only; openings cover all surfaces and cannot exceed gross area. Intermediate quantities are not rounded. RICS NRM2(2021) informs measurement boundaries, not a claim to implement every deduction rule.
  • https://www.rics.org/content/dam/ricsglobal/documents/standards/october_2021_nrm_2.pdf
  • Masonry/tiles: repeating module with joint, not a cutting layout; boundaries, bond and patterns need project take-off. No mortar, grout or strength calculation.
  • Paint uses practical product-datasheet coverage per whole coat. Plaster is wet volume only, not mix constituents. Stock matches product/unit and is allocated to this work.
  • Excavation is a vertical box only, without shoring/slope design. Swell and backfill ratio are project soil data, not code values. Backfill factor=loose/compacted volume; not an additional percentage counted twice.
  • Supply is separate from consumption; packs are whole. Excavation trips use loose volume and declared capacity; weight/road limits may increase trips. Results do not authorize construction.

Worked example

One 10.00 m × 3.00 m wall, deducting 2.00 m² of openings, using 400 × 200 mm block faces with a 5% waste allowance.

Worked example results
ResultValue
Gross measured area30 m²
Total openings across all surfaces2 m²
Net measured area28 m²
Repeating module area including joint0.08 m²
Unrounded theoretical consumption350 blocks
Loss allowance on theoretical only17.5 blocks
Requirement including loss before stock367.5 blocks
Compatible stock used0 blocks
Whole purchase packs or batches368 units
Purchased quantity, not consumption368 blocks
Calculated surplus assuming continued compatibility0.5 blocks

These figures are produced by the same calculator engine used on this page.

Frequently asked questions

Does the count include mortar?
No. The count uses the block face area and ignores joint thickness. Mortar volume needs an approved mix and joint dimension, which this engine does not assume.
Why is the result always a whole number?
Blocks cannot be ordered in fractions, so the total after waste is rounded up to the next whole block.
Can I model several identical walls at once?
Yes — the number-of-walls input multiplies the gross area before openings are deducted.
What block size should I enter?
The face length and height of the block specified for your works. No standard block size is assumed for you.

Next step and related links

Free calculators are open to everyone, and CSV export is free for everyone too. Project saving and PDF/Excel reports come with Professional, and integrated workflows with Premium.