Air Changes per Hour (ACH) Calculator
Calculate air changes per hour for a space.
Project & Input Data
Embedded standards & references
- Continuity Q=vA and volume balance Q=V/t; no embedded code limits
Results are engineering aids and require verification by a qualified professional before use on a real project.
Engineering Assumptions
Direct calculation — Single physical identity with declared scope
- No system selection or ventilation/fire/health compliance. ACH is nominal room-volume turnover, not distribution, outdoor air or clearance time; duct velocity is a mean at actual clear area.
- Tank usable volume is separate from dead volume/freeboard; no assumed refill credit or fire storage. Pump capacity is an independent comparison at the same duty head, not a curve/NPSH check; simultaneity lies between0and100%.
- Converter input is kW, L/s, Pa or °C by mode; absolute temperature, not temperature difference; nothing below absolute zero. NIST factors have published finite precision, not all exact.
- https://nvlpubs.nist.gov/nistpubs/Legacy/SP/nistspecialpublication811e2008.pdf
Formula Summary
- ACH=Q(m³/h)/V; mean duct velocity=Q(m³/s)/clear area
- Usable tank=daily demand×days+reserve; water=usable+dead; height=water/area+freeboard
- Pump comparison=max(daily demand/(hours×3600),peak×simultaneity/100)
- IT Btu/h≈0.2930711W; TR=12000ITBtu/h≈3516.8532W; conventional inH₂O=249.0889Pa; international ft³=.028316846592m³
Definitions and fixed factors
| Factor | Value |
|---|---|
| BtuIT/h→W | 0.2930711 |
| TR→W | 3516.8532 (12000×0.2930711) |
| inH₂O→Pa | 249.0889 |
| ft³→m³ | 0.028316846592 |
NIST2008 published precision; TR derived from12000BtuIT/h at the same precision; not design limits
Results
Enter your data and press Calculate to see the results.
Engineering Insight
The resulting change rate depends directly on the accuracy of the entered room volume.
Recommended Action
Compare the computed ACH against the minimum required for the space type before finalising the system design.
Ventilation rates are usually stated either as an airflow or as air changes per hour, and reviewers ask for both. This page converts between them for a single space: enter the room volume with the airflow to read the resulting ACH, and a target ACH to read the airflow it demands.
Method and assumptions
Single physical identity with declared scope
- ACH=Q(m³/h)/V; mean duct velocity=Q(m³/s)/clear area
- Usable tank=daily demand×days+reserve; water=usable+dead; height=water/area+freeboard
- Pump comparison=max(daily demand/(hours×3600),peak×simultaneity/100)
- IT Btu/h≈0.2930711W; TR=12000ITBtu/h≈3516.8532W; conventional inH₂O=249.0889Pa; international ft³=.028316846592m³
- No system selection or ventilation/fire/health compliance. ACH is nominal room-volume turnover, not distribution, outdoor air or clearance time; duct velocity is a mean at actual clear area.
- Tank usable volume is separate from dead volume/freeboard; no assumed refill credit or fire storage. Pump capacity is an independent comparison at the same duty head, not a curve/NPSH check; simultaneity lies between0and100%.
- Converter input is kW, L/s, Pa or °C by mode; absolute temperature, not temperature difference; nothing below absolute zero. NIST factors have published finite precision, not all exact.
- https://nvlpubs.nist.gov/nistpubs/Legacy/SP/nistspecialpublication811e2008.pdf
Worked example
A 150 m³ room supplied with 900 m³/h, checked against a target of 8 air changes per hour.
| Result | Value |
|---|---|
| Nominal air changes, not outdoor air | 6 ACH |
| Airflow on room-volume basis | 900 m³/h |
| Flow L/s | 250 L/s |
| Nominal volume-change time, not clearance | 10 min |
These figures are produced by the same calculator engine used on this page.
Frequently asked questions
- Where does the target ACH come from?
- You enter it. It is a criterion taken from the standard or space classification governing your project; the tool holds no ventilation rate table.
- Does it size a fan or duct?
- No. It gives the airflow relationship only. Duct dimensions come from the Duct Sizing calculator, and pressure from the external static pressure tool.
- Which units are used?
- Volume in cubic metres and airflow in cubic metres per hour, so ACH is simply airflow divided by volume.
- Does a higher ACH mean better air quality?
- Not by itself. ACH describes how often the air volume is replaced; outdoor air proportion, filtration and distribution decide the actual result and are outside this calculation.
Next step and related links
Related calculators
- Airflow / CFM CalculatorHVAC Design
- Duct SizingHVAC Design
- Fresh Air CalculatorHVAC Design
Free calculators are open to everyone, and CSV export is free for everyone too. Project saving and PDF/Excel reports come with Professional, and integrated workflows with Premium.


